您的位置: 标准下载 » 国际标准 » BS 英国标准 »
热门标准
下载排行

BS ISO 6621-5-2006 内燃机.活塞环.质量要求

作者:标准资料网 时间:2024-04-20 09:11:38  浏览:8486   来源:标准资料网
下载地址: 点击此处下载
【英文标准名称】:Internalcombustionengines-Pistonrings-Qualityrequirements
【原文标准名称】:内燃机.活塞环.质量要求
【标准号】:BSISO6621-5-2006
【标准状态】:现行
【国别】:英国
【发布日期】:2006-01-30
【实施或试行日期】:2006-01-30
【发布单位】:英国标准学会(BSI)
【起草单位】:BSI
【标准类型】:()
【标准水平】:()
【中文主题词】:缺陷;等级(质量);内燃机;作标记;材料;材料规范;机械工程;摩托车;包装件;工作特性;活塞环;产品规范;质量;质量条件;质量控制;质量要求;道路车辆;规范(验收);规范;公差(测量);可见特征
【英文主题词】:
【摘要】:ThispartofISO6621specifiesthosequalityaspectsthatarecapableofdefinitionbutnotnormallyfoundonadrawingspecification.Itcoversthefollowing:—single-piecepistonringsofgreycastironorsteel;—multi-piecepistonrings(oilcontrolrings)consistingofcastironpartsandspringcomponents;—single-pieceandmulti-pieceoilcontrolringsofsteel,i.e.oilcontrolringsintheformofstripsteelcomponentsorsteelsegments(rails)withspringexpandercomponents.Inadditiontospecifyingcertainofthelimitsofacceptancerelatingtoinspectionmeasuringprinciples(coveredbyISO6621-2),thispartofISO6621alsocoversthosefeaturesforwhichnorecognizedquantitativemeasurementproceduresexistandwhichareonlycheckedvisuallywithnormaleyesight(spectaclesifwornnormally)andwithoutmagnification.Suchfeatures(superficialdefects)areadditionaltothestandardtolerancesofringwidth,radialwallthicknessandclosedgap.ThispartofISO6621doesnotestablishacceptablequalitylevels(AQL),itbeinglefttomanufacturerandclienttodecidetheappropriatelevelsjointly.Inthiscase,therecommendationsofISO2859arefollowed.ThispartofISO6621specifiesthequalityrequirementsofpistonringsforbothreciprocatinginternalcombustionenginesandcompressorsworkingunderanalogousconditions.Itisapplicabletoallsuchringsofadiameter≤200mm.
【中国标准分类号】:J92
【国际标准分类号】:43_060_10
【页数】:24P;A4
【正文语种】:英语


下载地址: 点击此处下载
返回跳至顶部
Product Code:SAE J1467
Title:Clip Fastener Fitting
Issuing Committee:Hydraulic Hose And Hose Fittings Committee
Scope: This SAE standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment, primarily in mining applications.
Rationale: This SAE standard covers material and dimensional requirements of steel clip fastener fittings. These fittings are intended for use in hydraulic systems on industrial equipment, primarily in mining applications.Product Code:SAE J1489
Title:Heavy Truck and Bus Retarder Downhill Performance Mapping Procedure
Issuing Committee:Truck And Bus Transmission Committee
Scope:The procedure covers the estimation of the total retardation capability available to a specific vehicle from:Natural retardation (rolling resistance, aerodynamic drag, etc).Engine dragEngine, integral automatic transmission, driveline or trailer-axle retardersIt assumes that foundation brakes are not used for maintaining speed on long mountain descents. Retardation is rated in terms of the maximum grades on which stable control speeds can be maintained for each gear over the range of highway speeds appropriate to that gear. For each gear, the calculation procedure determines maximum grades for at least four values of control speed ranging from the vehicle velocity corresponding to full load governed engine rpm, to the vehicle velocity corresponding to the engine rpm at minimum (idle) speed. In addition, the calculation procedure provides information on the total retarding power available for each gear.PurposeThis procedure provides a uniform method for calculating and reporting the steady-state control speed maintainable by either engine, integral automatic transmission, driveline, or trailer-axle retarders employed by heavy trucks and buses operating on downgrades. It provides a practical method of predicting retarder performance in a specified vehicle installation using data describing retarder performance characteristics and other vehicle design variables. It is intended to assist in the proper selection of a retarder by matching stated retarder performance capabilities with particular vehicle functional requirements.